Skip to main content

Guide

What a cold-storage PM visit covers, task by task

The checklist behind a preventative maintenance visit on a lab refrigerator, freezer, or ULT freezer: each task, how often it is done, and which ones you can do in-house.

Updated September 18, 20265 min readBy Scientific Refrigeration

Nearly every cold storage failure we see was visible months earlier to someone who knew where to look. A condenser coil packed with dust. A gasket that no longer seals at the bottom corner. A fan bearing that had started to whine. A controller reading two degrees warm. Preventative maintenance is the discipline of looking before the failure, on a schedule, and writing down what was found. This guide covers what a PM visit includes, how often, and what you can do yourself.

What a PM visit covers

A preventative maintenance visit on a laboratory refrigerator, freezer, or ultra-low freezer works through the parts that wear and the conditions that cause wear. This is the basic PM checklist. It can be customized to your SOPs or expanded to cover anything not on it, and calibration, electrical safety testing, and alarm testing can be bundled into the same visit to save you a second one.

The condenser and airflow

The condenser is where the unit sheds heat. A coil coated in dust cannot do that, so pressure rises in the system, the compressor runs hotter and longer, and capacity drops. The technician cleans the condenser coil and filter, checks the condenser fan for noise and airflow, and confirms the unit has the clearance it needs behind and above.

Door, gaskets, and heaters

A gasket that leaks lets moist room air in. On a refrigerator that means frost on the evaporator and a compressor that works harder. On a ULT freezer it means frost that grows until the door will not seal, and a runaway that follows. The technician inspects the gasket all the way around, checks the door alignment and closure, and on ULT units checks the door frame heater, which prevents the gasket from freezing to the frame.

Evaporator and defrost

The evaporator is checked for ice buildup, and on auto-defrost units the defrost heater, timer or control, and drain are checked. A blocked drain is a common cause of water inside a refrigerator and ice on the floor of a freezer.

Fans and motors

Evaporator and condenser fan motors are checked for noise, vibration, current draw, and blade condition. Fan failures are gradual and audible; catching one on a PM visit is far cheaper than finding it after the unit has warmed.

Compressor and refrigeration system

The technician listens to and observes the compressor on startup and running, checks operating pressures and temperatures where the design allows, looks for oil residue that indicates a leak, and checks electrical connections at the compressor and contactor. On a cascade ULT freezer, both stages are checked. Any sign of a refrigerant leak is investigated rather than topped up.

Controls, sensors, and alarms

The controller reading is compared with an independent reference thermometer. Alarm setpoints are confirmed, and the alarm is tested, including remote contacts if you use monitoring. Battery backups for alarms and controllers are checked. On units with data logging, the log is reviewed for trends.

Electrical

Power cord and plug condition, connections at the terminal block, contactor contacts, and current draw against the nameplate. Loose connections heat up and fail; they are found on PM visits.

The record

Every visit ends with a written report: what was checked, what was found, what was corrected, what is wearing and should be planned for, and any readings taken. That report is the PM’s lasting value. Over a few years it becomes the condition history that tells you whether a unit deserves its next repair.

Calibration alongside PM

Calibration is a separate task often done on the same visit: the unit’s temperature sensors and display are checked against a reference traceable to national standards, at the points your program requires, and a certificate documents the result. A PM visit without calibration leaves you with a well-maintained unit whose display may or may not be telling the truth. Our calibration is NIST-traceable, and the records are written for your quality system.

Calibration is typically annual, and it pairs with a six-month PM cadence: two PM visits and one calibration a year, bundled. Many labs send calibration out separately without realizing it can be done on the same visit, at a lower total cost.

How often

Every six months is our standard contract offering and the baseline we recommend. Quarterly suits heavy use, which is common in California: warm or dusty rooms, high door traffic, and units critical to compliance. Annual is available, and it is often not enough for anything beyond a lightly used refrigerator in a cool room. It is easier to start at six months or quarterly than to move there later; doubling the frequency after the fact reads as doubling the cost, even when it is the right call.

  • General laboratory refrigerators and -20°C freezers: every six months, quarterly if the room is warm or dusty or the unit is critical.
  • Ultra-low freezers: every six months at minimum, quarterly under heavy use. They run at the edge of their capacity by design, and the condenser and gasket problems that kill them develop faster.
  • Blood bank refrigerators, plasma freezers, and other regulated units: at the interval your accreditation and SOP require, which is often twice a year plus the alarm and recorder checks your program specifies.
  • Walk-in cold rooms: twice a year is common, with attention to door hardware, evaporator fans, defrost, and drains.
  • Cryogenic freezers and LN2 storage: per the manufacturer and your program, with particular attention to fill systems, alarms, and vacuum condition.

If a unit starts failing between visits, the interval is too long for that unit.

What you can do in-house

Between visits, facilities or lab staff can reasonably handle:

  • Checking door gaskets for tears, hardening, and frost, and wiping them clean.
  • Keeping the required clearance around the unit and keeping the top clear.
  • Reviewing the temperature log weekly and noting any drift or widening cycle.
  • Listening for new noises when passing the unit.
  • Keeping the unit loaded so air can move: nothing against the back wall, nothing blocking vents.

Leave condenser cleaning, refrigerant work, electrical diagnosis, compressor assessment, and traceable calibration to a technician. Condenser cleaning in particular is on every PM visit, at minimum every six months and quarterly where the unit works hard.

Why the records matter

When a unit finally has a serious failure, the decision to repair or replace comes down to its history. A unit with five years of clean PM reports and one failure is a repair. A unit with a report every year that says the compressor is running hot and the gasket has been replaced twice is a different conversation. Without the records you are guessing, and guessing under time pressure with product at risk is how bad decisions get made.

When to call us

Our preventative maintenance and calibration programs are built around the equipment you have, how hard it runs, and what your compliance program requires. If a unit is already showing wear, our service and repair team can inspect it first. For regulated equipment, our certification and validation work produces the documentation your inspector expects.

Questions

Frequently asked

How often should a lab freezer have preventative maintenance?

Every six months is our standard contract offering and the baseline we recommend. Quarterly suits heavy use, which is common in California. Annual is available but often not enough, and it is easier to start at six months or quarterly than to increase the interval later.

What is the difference between PM and calibration?

PM is mechanical: cleaning, inspecting, and adjusting the parts that wear. Calibration checks the temperature sensors and display against a traceable reference and documents the result. They are often done on the same visit but they are different tasks with different records.

Can our own facilities staff do the PM?

Some of it. Checking gaskets, keeping clearance, and reviewing temperature logs are reasonable in-house tasks. Condenser cleaning, refrigerant work, electrical diagnosis, compressor assessment, and calibration against a traceable reference are technician work. Condenser cleaning is on every PM visit.

What does a maintenance contract include?

The basic PM checklist in this guide, customized to your SOPs or expanded to cover anything not on it. Calibration, electrical safety testing, and alarm testing can be bundled into the same visit, which saves money. Any recurring service agreement, whether PM, calibration, maintenance, or electrical safety, qualifies you for our contracted-customer rates.

Keep reading

More like this, a few times a year

Equipment care guides and service news from the technicians who write them. No sales sequences. Unsubscribe with one click.

Equipment care tips and service news, a few times a year. Unsubscribe anytime.

Ready when you are

Seeing this on your own equipment?

Request service and a dispatcher will call to confirm, or ask a technician a question first.

24/7 emergency service · Dispatch confirms every request by phone.

Call nowRequest service

Request service

A few quick questions, then a dispatcher calls you to confirm.

What do you need?

Service type

Equipment failing right now? Don’t wait for a callback. 24/7 emergency service, and the line is answered 24/7.