A freezer alarm at four in the afternoon on a Friday forces three decisions at once: how to protect what is inside, whether to fix the unit, and whether to keep it at all. Made in that order, they are manageable. Made in a panic, they get expensive. This guide is the order we walk customers through.
First: protect the product
Nothing else matters until the product is safe. If the unit is warming and you cannot stop it, the options are to move the product to another unit you own, to move it to a rental, or to pack it in dry ice or LN2 for the short term.
Moving to another unit you own is fastest if you have the space, but a freezer that was already full has just become an overloaded freezer, and overloaded freezers fail too. A rental unit arriving on site removes that risk. Dry ice buys hours, not days, and it is a bridge to one of the other two.
Call for the rental at the same time you call for the repair. The rental is often the least expensive part of the whole event, and it turns a crisis into a scheduling problem. Our rental fleet covers ultra-low freezers, refrigerators, freezers, plasma freezers, and blood bank refrigerators.
Second: understand the failure
Before deciding anything, find out what actually failed. A technician can usually tell you within the first visit whether this is a component failure (a fan, a controller, a relay, a gasket, a single compressor), a system failure (a refrigerant leak, a cascade stage lost, a heat exchanger), or a symptom of something outside the unit (a room that is too warm, a power problem, a drain that is blocked).
The answer changes everything. A failed door heater on a five-year-old freezer is a repair. A second cascade compressor failure on a twelve-year-old freezer that had its first one two years ago is a different conversation.
Third: weigh repair against replacement
These are the factors, roughly in order of weight.
Repair cost against replacement cost
There is no fixed rule, and the answer varies by customer. Some keep older units running because they are reliable workhorses. Others repair only because it fits this year’s budget, which is not always the right call. A well-maintained unit with one expensive failure can still be worth fixing. A cheap repair on a unit with a long failure history may not be.
Some numbers, as of 2026, from our own recent jobs and quotes. A ULT freezer rebuild runs roughly $7,000 to $10,000. A new Eppendorf ULT runs about $30,000, and some models $60,000. A new ULT from other brands can be around $10,000, which raises the question of what happens to the old unit. Usually it goes to a landfill, and that undercuts the apparent saving. Repairing keeps a working unit out of the landfill, which matters to facilities with a sustainability target and to anyone counting the whole cost.
Age and condition
Laboratory refrigeration typically gives a long service life with maintenance, and units well past ten years are common and often fine. What ages a unit is not the calendar but the hours the compressor has run, the condition of the insulation and gaskets, and how well it was maintained. Ask the technician for an honest read on the condition of the parts that were not the problem today.
Failure history
One failure is an event. Two in a short period is a pattern. A unit that has needed a major repair every year is telling you its economics have changed, even if each individual repair looked reasonable.
Parts availability
Some older units are still supported and some are not. If a control board or a compressor is no longer available, a repair that looks easy on paper can take weeks or become impossible. Your technician will know.
How long you can be without it
If the unit is your only -80°C freezer and the rental is on site, you have time to make a good decision. If it is a walk-in that the whole facility depends on, downtime itself is a cost, and a faster path may be worth more than a cheaper one.
Energy and running cost
Older ultra-low freezers in particular use a great deal more electricity than current designs. Over years of continuous operation, that difference is real money and is part of the replacement calculation.
Compliance
If the unit is validated, any major repair or replacement means re-qualification: mapping, calibration, documentation. Factor that in for both options. A replacement also means a new validation, but a repaired unit may need one too.
If you repair
Have the repair done by someone who will tell you what else they saw. A good service report on a repair visit reads like a condition assessment: what failed, what was replaced, what is wearing, and what to expect. Then put the unit on a maintenance schedule so the next failure is caught early.
If you replace
You have two sources through us, and we will be honest about which fits.
Inspected used equipment from our own shop. Every used unit we sell has been through our technicians: inspected, parts repaired or replaced as needed, and tested before it leaves. Our rental units go through the same inspection; some of them come to us as scratch-and-dent from manufacturers. For many applications a used unit is the right value, and a technician who knows the unit is the one who installs it.
New equipment from our partner company, Legacy Lab Supplies. We do not sell new equipment. Legacy Lab Supplies does, from the major manufacturers, and shares our warehouse, so a new unit can be delivered, installed, validated, and maintained by the same team from order to startup.
Either way, the installation and validation are the same work, done by the same technicians.
A decision checklist
Before you decide, you should be able to answer:
- Is the product safe right now, and for how long?
- What exactly failed, and is it a component, a system, or the environment?
- What is the repair estimate, and what is a comparable replacement worth?
- What is this unit’s failure history over the last few years?
- Are parts available, and how long will they take?
- What does downtime cost per day, and is a rental on site?
- What re-qualification does each option require?
If you can answer all seven, the decision usually makes itself.
When to call us
Our emergency line is answered 24 hours a day. Call it for the repair and the rental in the same conversation. When the repair is done, or when it is time to replace, our service and repair team will give you a straight assessment, and our equipment rental and used equipment sales will cover what comes next. New equipment is at Legacy Lab Supplies.